Wind Power Tower Kits
Southwest Wind Power Tower Kits
________________________________________________
The most difficult challenge installing a Wind Power Generator turbine is assembling and erecting a tower.
Engineers at Southwest Wind Power Generator designed towers that are easy to install.A number of heights for each product are available.
Keep in mind, larger Wind Power generators require more complex tower designs. None of our Wind Power Generator towers require any welding or machining and only our largest towers may require concrete. Most designs can be installed within a few hours to a day. Lastly, all work with Southwest Wind Power Generator towers is done on the ground.No climbing ever again, and no cranes!
You will NEVER need to climb a tower - not ever!
Tower Kits & Manuals
Whisper 100/200 Towers
Whisper 100/200 24'$505
Whisper 100/200 30'
Whisper 100/200 50'
Whisper 100/200 65'
Whisper 100/200 80'
Whisper 500 Towers
Whisper 500 30'
Whisper 500 42'
Whisper 500 70'
Call 435.686.2263
Customer Notice:
Southwest Wind Power recommends our Tower Kits for your Wind Power Generator
However, you can build your own tower by using the proper manual (above)
Only the Wind Power Generator Pipe is locally supplied by buyer because of exceedingly high freight costs.
These long lengths cannot be shipped by UPS, and must go on 18-Wheeler flatbed trucks!
Your local "Steel & Ranch Supply can easily deliver it easily to your site.
for "Thrust Load" Specifications on Whisper Towers
See what nice folks we are...
Part 24'
(7.2m)30'
(9.0m)50'
(15.0m)65'
(19.5m)80'
(24.0m)Tower Base 1 1 1 1 1 Coupler/Lower Wire Base 0 1 2 3 4 Coupler/Top Wire Base 1 1 1 1 1 Turbine Mount Coupler 1 1 1 1 1 Tower Pivot Coupler 1 1 1 1 1 Gin Pole Coupler 0 0 0 1 1 Gin Pilot Coupler 0 1 1 1 1 Gin Pole Top 0 1 1 1 1 Gin Pole Top Link 0 1 1 1 1 Coupler Bolts 8 16 20 28 32 Cable Thimbles 4 8 12 16 20 Cable Clamps 8 16 24 32 40
Tower Pipe Requirements
Tower Kits use 2.5 inches (63.5 mm) CQ40 fence pipe or schedule 40 water pipe
(actual outer diameter of pipe is 2.875 inches (73 mm)Specifications and Pipe Lengths
Only the Pipe is locally supplied by the buyer because of exceedingly high freight costs.
These long lengths cannot be shipped by UPS, and must go on 18-Wheeler flatbed trucks!
Your local "Steel & Ranch Supply" can easily deliver to your site.
24'
(7.2m)30'
(9.0m)50'
(15.0m)65'
(19.5m)80'
(24.0m)Poles 1 x 24' (7.2m) 1 x 13' (3.9m)
1 x 17' (5.1 m)2 x 15' (4.5m)
1 x 20' (6.0m)3 x 15' (4.5m)
1 x 20' (6.0m)4 x 15' (4.5m)
1 x 20' (6.0m)Gin Pole NA 1 x 15' (4.5m) 1x 19' (5.7m) 1 x 20' (6.0m)
1 x 6' (1.8m)1 x 20' (6.0m)
1 x 13' (3.9m)Guy Radius 15' (4.5m) 20' (6.0m) 25' (7.5m) 33' (9.9m) 40' (12.9m) Auger Size 36" (91.5cm) 48" (121.9cm) 48" (121.9cm) 60" (152.4cm) 60" (152.4cm) Anchor Hole Diameter 1.5' (.45m) 2' (.6m) 2' (.6m) 2' (.6m) 2' (.6m) Anchor Hole Depth 3' (.9m) 3' (.9m) 3' (.9m) 3' (.9m) 4' (1.2m) Concrete verdana 12" (30.5cm) 9" (22.9cm) 10" (25.4cm) 12" (30.5cm) 12" (30.5cm) Anchor Points Each tower uses 4 anchor points
Tower Kit Installation
As easy as 1... 2... 3!
1... Choose your site. Unpack your new AIR X Wind Power Generator module and tower kit.2... Assemble wind module, attach to tower, attach tower couplers (guy wires already attached) to your pole.
3... Mount pipes to base connector and pin using base staples.
Connect necessary guy wires, raise tower and anchor remaining guy wires.
Note: With 45 foot tower, assemble the included gin pole Setup Kit to easily raise Wind Power tower
The 27' Guyed Tower Kit
Specs Sheet
The 45' Guyed Tower Kit
Call - 435.686.2263
Aside from Wind Power New! 29' EZ Tower, all of Southwest WindPower tower kits include everything except: $208
1) Pipe material
2) Anchors
3) Power wires (all supplied by electrician)To keep your costs low and to consider site variables, Wind Power Generator components should be purchased locally. When selecting Wind Power Generator materials for Wind Power construction of your tower, please consider the following:
Pipe Material: For most conditions, we recommend “schedule 40” pipe with a wall thickness of .125” which is strong enough to resist most wind conditions. If you are using fence pipe material, make sure you ask for “SS40”. If you live were your winds will never exceed 80 mph (140 km) Wind Power we suggest using a thinner wall material such as a “schedule 20”. In conduit material, this is called “SS20”.
Anchors: The anchors are the most difficult part of installing a tower. Once you have them in the ground, the tower installation is easy. There are various soil materials that you should consider prior to installing your tower. The type of anchor should also vary. Our owner manuals have recommendations based on soil type.Power Wires: Because of Wind Power Generator size and variable length from Wind Power turbine to your batteries/inverter, it is impossible to know Wind Power proper wire size. Once you know Wind Power distance from Wind Power turbine to Wind Power batteries, see Wind Power Wind Turbine owners manual for Wind Power proper wire size.
VERY IMPORTANT:
Prior to installing your tower, read Wind Power owners manual thoroughly and make sure you understand Wind Power environmental conditions at your site prior to purchasing materials. We offer manuals that are free to download and review prior to purchase.
Wind Power Generator Wind Charts
Okay, Cowgirls! ...Ya better Rope 'em and make sure Your Cowboys are Prepared
You don't need Boots & Hat to be a Cowgirl or Cowboy. Just be true Americans!
Rise Above It all - It's Time to Cowboy Up, Pard !!
In Survival & War, 'Second Place' is the First loser
None of this is a game . . . it's your life
